Nanotechnology For Data Storage

High-density digital recording requires an extremely thin recording layer. As opposed to ATOMM (Advanced Super Thin Layer & High Output Metal Media Technology) technology, which was the first technology to allow the production of submicron-scale thin metal coatings, Nanocubic technology allows the production of nanometer-scale ultra-thin coatings (one nanometer = one-billionth of a meter). In addition, nano-particle technology is employed to create magnetic needle-shaped metal particles and plate-shaped barium-ferrite particles that are only a few tens of namometers in size, and a new high-molecular binder material and nano-dispersion technology are used to ensure uniform dispersion of the particles. Using Nanocubic technology, it is now possible to create data cartridges that offer low noise, excellent storage characteristics, and capacities in excess of one terabyte.

Fujifilm nanocubic is a combination of 3 unique nano technologies.

1. Coating Technology
An advanced precision coating process creates layers 5 times thinner than exsiting technologies.

 2. Particle Technology

Creates two unique new ferromagnetic particles that are both just tens of nanometers in size:acicular ferromagnetic alloy and tabular ferromagnetic hexagonal barium ferrite.

3. Dispersion Technology

Employing a specially formulated polymer binder creates even dispersion and uniform packed structure.

Self-Powered Nanosystem With Wireless Data Transmission

 

Fabrication of a single nanodevice is no longer the state of the art in nanotechnology. The leading edge – and also currently the most challenging area in nanotechnology – is research that leads to a self-powered nanoscale system that is driven by the energy harvested from its environment and that can perform its work independently and sustainable. This is a key step toward self-powered nanotechnology, which is vitally important for medical science, environmental monitoring, defence technology and even personal electronics. Not to mention that it will lead to practically usable nanotechnology devices.

Each sensor is not required to work continuously and simultaneously, instead, it will have a 'blinking' working mode with a standby status and active status" says Wang. "The standby mode is normally longer, while the active mode is shorter. The energy scavenged and stored during the standby status can be used to drive it in the active mode. This means that these sensors periodically sample from their working environment and transmit data within a fraction of second. We can use the nanogenerator to harvest energy from the environment and store most of the energy when the sensor is in the standby mode. Then the collected energy will be used to trigger the sensor and then process and transmit the data in the active mode."
 The nanogenerator fabricated by Wang's team is a free-standing cantilever beam that consists of a five-layer structure: a flexible polymer substrate; densely packed zinc oxide nanowire textured films on its top and bottom surfaces; and electrodes on the surfaces.
 When it was strained to 0.12% at a strain rate of 3.56 % S-1, the measured output voltage reached 10 V, and the output current exceeded 0.6 µA (corresponding power density 10 mW/cm3).

Key Properties of Polymer Thin Films and Membranes

Researchers at the National Institute of Standards and Technology (NIST) have demonstrated* a measurement technique that reliably determines three fundamental mechanical properties of near-nanoscale films. The technique, which highlights the challenge of making mechanical measurements on an object with at least one dimension comparable to the size of a virus, should enable better design and engineering for a variety of thin-film technologies, particularly reverse-osmosis membranes for water purification.

5 Surprising Uses For Carbon Nanotubes

First discovered under an electron microscope over a half a century ago, carbon nanotubes have become one of the most sought after materials today. The tiny structures are used in dozens of applications that touch nearly every industry, including aerospace, electronics, medicine, defense, automotive, energy, construction, and even fashion.

Carbon nanotubes (aka CNTs) are made from graphene sheets consisting of a single atomic layer of carbon atoms in a honeycomb framework that can be rolled into a tube measuring about a nanometer or, one billionth of a meter, in diameter.

At this scale, these cylindrical molecules defy the classic laws of physics with exceptional properties. Carbon nanotubes have excellent electrical conductivity, the ability to withstand high working temperatures, and the highest strength to weight ratio of any known material.